NEP throttle lock

Discussion in 'Mechanics Garage' started by dogger810, Mar 5, 2009.

  1. dogger810

    dogger810 New Member

    Joined:
    Sep 23, 2008
    Messages:
    6
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Noblesville, IN
    Does anyone know a good place to purchase an NEP throttle lock?
    Thanks,
    Tom
     
  2. Y2Kviffer

    Y2Kviffer Insider

    Country:
    United States
    Joined:
    May 12, 2008
    Messages:
    1,204
    Likes Received:
    31
    Trophy Points:
    78
    Location:
    RALEIGH, NC
    Map
    I got mine from a local Cycle Gear for about $20.
     
  3. 300shooter

    300shooter New Member

    Joined:
    Oct 29, 2007
    Messages:
    391
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    armpit of ontario (Windsor)
    Ever consider throttlemeister? I know they cost more but sweet looking and really user friendly.:thumbsup:
     
  4. Interceptor1

    Interceptor1 New Member

    Joined:
    Dec 6, 2006
    Messages:
    83
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Quebec
  5. drewl

    drewl Insider

    Country:
    United States
    Joined:
    Nov 13, 2007
    Messages:
    5,760
    Likes Received:
    6
    Trophy Points:
    83
    Location:
    Virginia Beach, Va
    Map
    I got mine online. Forget where, but it was 22.50 with shipping. Worth every penny.
    I use it for a few seconds here and there to stretch my wrist, not so much like the cruise control on a car. So for the little that I use it, the throttle meister was just too much.
     
  6. Pliskin

    Pliskin New Member

    Country:
    United States
    Joined:
    Jun 3, 2008
    Messages:
    3,699
    Likes Received:
    0
    Trophy Points:
    36
    Location:
    Morris County, New Jersey
    Map
    OK, my noob question.

    How do these work (whether its Throttlemeister or NEP? Is it as simple as clamping it onto the handle bar, and to "activate" it, you simply click it into place so that it holds the throttle in the current position?

    Is it necessary to move any things - break lines, etc.?

    Thanks. I've never even considered one of these, but as I get older (i.e. fatter), sounds like a nice little addition.
     
  7. drewl

    drewl Insider

    Country:
    United States
    Joined:
    Nov 13, 2007
    Messages:
    5,760
    Likes Received:
    6
    Trophy Points:
    83
    Location:
    Virginia Beach, Va
    Map
    The NEP is a simple plastic clamp that goes between the throttle grip and the switch housing. On the 5th gen there is no modding needed. The 6th gen requires some trimming of plastic from the lock.
    To activate it all one needs to do is flip a lever with the thumb. Then flip it down when done. It takes 10 minutes to install.

    The throttle meister is a bit more complex, but I don't own one so I will not speak to it.

    [​IMG]
    That plastic lever is the NEP on the right clip on.(the pic is from a fork removal project. it is not necessary to remove the clip on to install the NEP)
     
  8. Badbilly

    Badbilly Official VFRWorld Troll Of The Year!

    Country:
    United States
    Joined:
    Sep 9, 2007
    Messages:
    15,047
    Likes Received:
    52
    Trophy Points:
    48
    Installed a Throttlemeister on my bike in about 93-94. Aerorspace level machining-major parts are stainless steel. Unobtrusive and part of the package includes bar end weight for the left bar. Zero maintenence/zero problems.
     
  9. 300shooter

    300shooter New Member

    Joined:
    Oct 29, 2007
    Messages:
    391
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    armpit of ontario (Windsor)
    I only know about the throttlemeister, takes about 2 minutes to install, unscrew the old end weights, screw in the new ones. They may need adjusting with the supplied spacers but really simple. To operate, twist the weight back with your last two fingers to engage, roll forward or roll throttle forward to disengage. Best part is you can't tell the difference from stock , unless you get the milled or polished S/S version. I've got a set for 6th gen for sale, $75 and I'll ship 'em. They fit stock bars and heli's made after 04.
     
  10. Pliskin

    Pliskin New Member

    Country:
    United States
    Joined:
    Jun 3, 2008
    Messages:
    3,699
    Likes Received:
    0
    Trophy Points:
    36
    Location:
    Morris County, New Jersey
    Map
    Thank you for the photo, Drewl, and thanks for the additional info on the throttlemeister, 300.

    I might consider your offer for the throttlemeister, but my bike is a 5th generation.

    Time to do some research and look at these 2 options in person.
     
  11. shorawitz

    shorawitz New Member

    Joined:
    May 28, 2010
    Messages:
    92
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Glendora, CA
    Map
    Hey 300shooter! Don't suppose you still have your throttlemeister?
     
  12. shorawitz

    shorawitz New Member

    Joined:
    May 28, 2010
    Messages:
    92
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Glendora, CA
    Map
Related Topics

Share This Page